[Feb-2024] Fortinet NSE7_SDW-7.0 Dumps – Secret To Pass in First Attempt [Q30-Q51]

5/5 - (2 votes)

[Feb-2024] Fortinet NSE7_SDW-7.0 Dumps – Secret To Pass in First Attempt

Fortinet NSE7_SDW-7.0 Exam Dumps [2024] Practice Valid Exam Dumps Question

NEW QUESTION 30
Which two protocols in the IPsec suite are most used for authentication and encryption? (Choose two.)

Encapsulating Security Payload (ESP)

Secure Shell (SSH)

Internet Key Exchange (IKE)

Security Association (SA)

NEW QUESTION 31
What are two reasons why FortiGate would be unable to complete the zero-touch provisioning process? (Choose two.)

The FortiGate cloud key has not been added to the FortiGate cloud portal.

FortiDeploy has connected with FortiGate and provided the initial configuration to contact FortiManager

The zero-touch provisioning process has completed internally, behind FortiGate.

FortiGate has obtained a configuration from the platform template in FortiGate cloud.

A factory reset performed on FortiGate.

NEW QUESTION 32
Which diagnostic command can you use to show the member utilization statistics measured by performance SLAs for the last 10 minutes?

diagnose sys sdwan intf-sla-log

diagnose sys sdwan health-check

diagnose sys sdwan log

diagnose sys sdwan sla-log

NEW QUESTION 33
Refer to the exhibits.

Which two statements about the IPsec VPN configuration and the status of the IPsec VPN tunnel are true? (Choose two.)

FortiGate does not install IPsec static routes for remote protected networks in the routing table.

The phase 1 configuration supports the network-overlay setting.

FortiGate facilitated the negotiation of the T_INET_1_0_0 ADVPN shortcut over T_INET_1_0.

Dead peer detection is disabled.

NEW QUESTION 34
Refer to the exhibit.

The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured latency will make T_MPLS_0 the new preferred member?

When T_INET_0_0 and T_MPLS_0 have the same latency.

When T_MPLS_0 has a latency of 100 ms.

When T_INET_0_0 has a latency of 250 ms.

When T_N1PLS_0 has a latency of 80 ms.

NEW QUESTION 35
Which diagnostic command can you use to show the configured SD-WAN zones and their assigned members?

diagnose sys sdwan zone

diagnose sys sdwan service

diagnose sys sdwan member

diagnose sys sdwan interface

NEW QUESTION 36
Refer to the exhibit.

Based on the exhibit, which statement about FortiGate re-evaluating traffic is true?

The type of traffic defined and allowed on firewall policy ID 1 is UDP.

FortiGate has terminated the session after a change on policy ID 1.

Changes have been made on firewall policy ID 1 on FortiGate.

Firewall policy ID 1 has source NAT disabled.

NEW QUESTION 37
In a hub-and-spoke topology, what are two advantages of enabling ADVPN on the IPsec overlays? (Choose two.)

It provides the benefits of a full-mesh topology in a hub-and-spoke network.

It provides direct connectivity between spokes by creating shortcuts.

It enables spokes to bypass the hub during shortcut negotiation.

It enables spokes to establish shortcuts to third-party gateways.

NEW QUESTION 38
What is the route-tag setting in an SD-WAN rule used for?

To indicate the routes for health check probes.

To indicate the destination of a rule based on learned BGP prefixes.

To indicate the routes that can be used for routing SD-WAN traffic.

To indicate the members that can be used to route SD-WAN traffic.

NEW QUESTION 39
Which two statements are true about using SD-WAN to steer local-out traffic? (Choose two.)

FortiGate does not consider the source address of the packet when matching an SD-WAN rule for local-out traffic.

By default, local-out traffic does not use SD-WAN.

By default, FortiGate does not check if the selected member has a valid route to the destination.

You must configure each local-out feature individually, to use SD-WAN.

NEW QUESTION 40
Refer to the exhibits.
Exhibit A –

Exhibit B –

Exhibit A shows a site-to-site topology between two FortiGate devices: branch1_fgt and dc1_fgt. Exhibit B shows the system global and system settings configuration on dc1_fgt.
When branch1_client establishes a connection to dc1_host, the administrator observes that, on dc1_fgt, the reply traffic is routed over T_INET_0_0, even though T_INET_1_0 is the preferredmember in the matching SD-WAN rule.
Based on the information shown in the exhibits, what configuration change must be made on dc1_fgt so dc1_fgt routes the reply traffic over T_INET_1_0?

Enable auxiliary-session under config system settings.

Disable tp-session-without-syn under config system settings.

Enable snat-route-change under config system global.

Disable allow-subnet-overlap under config system settings.

NEW QUESTION 41
Refer to the exhibit.

Which statement about the role of the ADVPN device in handling traffic is true?

This is a spoke that has received a query from a remote hub and has forwarded the response to its hub.

Two hubs, 10.0.1.101 and 10.0.2.101, are receiving and forwarding queries between each other.

This is a hub that has received a query from a spoke and has forwarded it to another spoke.

Two spokes, 192.2.0.1 and 10.0.2.101, forward their queries to their hubs.

NEW QUESTION 42

Two hub-and-spoke groups are connected through a site-to-site IPsec VPN between Hub 1 and Hub 2. The administrator configured ADVPN on both hub-and-spoke groups.
Which two outcomes are expected if a user in Toronto sends traffic to London? (Choose two.)

London generates an IKE information message that contains the Toronto public IP address.

Traffic from Toronto to London triggers the dynamic negotiation of a direct site-to-site VPN.

Toronto needs to establish a site-to-site tunnel with Hub 2 to bypass Hub 1.

The first packets from Toronto to London are routed through Hub 1 then to Hub 2.

NEW QUESTION 43
Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit A shows the source NAT (SNAT) global setting and exhibit B shows the routing table on FortiGate.
Based on the exhibits, which two actions does FortiGate perform on existing sessions established over port2, if the administrator increases the static route priority on port2 to 20? (Choose two.)

FortiGate flags the sessions as dirty.

FortiGate continues routing the sessions with no SNAT, over port2.

FortiGate performs a route lookup for the original traffic only.

FortiGate updates the gateway information of the sessions with SNAT so that they use port1 instead of port2.

NEW QUESTION 44
What is a benefit of using application steering in SD-WAN?

The traffic always skips the regular policy routes.

You steer traffic based on the detected application.

You do not need to enable SSL inspection.

You do not need to configure firewall policies that accept the SD-WAN traffic.

NEW QUESTION 45
Which two performance SLA protocols enable you to verify that the server response contains a specific value? (Choose two.)

http

icmp

twamp

dns

NEW QUESTION 46
Refer to the exhibit.

Which conclusion about the packet debug flow output is correct?

The original traffic exceeded the maximum packets per second of the outgoing interface, and the packet was dropped.

The reply traffic exceeded the maximum bandwidth configured in the traffic shaper, and the packet was dropped.

The original traffic exceeded the maximum bandwidth of the outgoing interface, and the packet was dropped.

The original traffic exceeded the maximum bandwidth configured in the traffic shaper, and the packet was dropped.

NEW QUESTION 47
Which two statements describe how IPsec phase 1 main mode is different from aggressive mode when performing IKE negotiation? (Choose two )

A peer ID is included in the first packet from the initiator, along with suggested security policies.

XAuth is enabled as an additional level of authentication, which requires a username and password.

A total of six packets are exchanged between an initiator and a responder instead of three packets.

The use of Diffie Hellman keys is limited by the responder and needs initiator acceptance.

NEW QUESTION 48
Which two statements about SLA targets and SD-WAN rules are true? (Choose two.)

When configuring an SD-WAN rule, you can select multiple SLA targets of the same performance SLA.

SD-WAN rules use SLA targets to check if the preferred members meet the SLA requirements.

SLA targets are used only by SD-WAN rules that are configured with Lowest Cost (SLA) or Maximize Bandwidth (SLA) as strategy.

Member metrics are measured only if an SLA target is configured.

NEW QUESTION 49
What are two reasons why FortiGate would be unable to complete the zero-touch provisioning process?
(Choose two.)

The FortiGate cloud key has not been added to the FortiGate cloud portal.

FortiDeploy has connected with FortiGate and provided the initial configuration to contact FortiManager

The zero-touch provisioning process has completed internally, behind FortiGate.

FortiGate has obtained a configuration from the platform template in FortiGate cloud.

A factory reset performed on FortiGate.

NEW QUESTION 50
Refer to the exhibits.

Which two conclusions for traffic that matches the traffic shaper are true? (Choose two.)

The traffic shaper drops packets if the bandwidth is less than 2500 KBps.

The measured bandwidth is less than 100 KBps.

The traffic shaper drops packets if the bandwidth exceeds 6250 KBps.

The traffic shaper limits the bandwidth of each source IP to a maximum of 6250 KBps.

NEW QUESTION 51
What are two common use cases for remote internet access (RIA)? (Choose two.)

Provide direct internet access on spokes

Provide internet access through the hub

Centralize security inspection on the hub

Provide thorough inspection on spokes

NSE7_SDW-7.0 Exam Dumps PDF Guaranteed Success with Accurate & Updated Questions: https://www.actualpdf.com/NSE7_SDW-7.0_exam-dumps.html

Leave a Reply Cancel reply