[Aug-2023] Updated JNCIP-SP JN0-663 Exam Questions BUNDLE PACK [Q18-Q33]

Rate this post

[Aug-2023] Updated JNCIP-SP JN0-663 Exam Questions BUNDLE PACK

Master The Juniper Content JN0-663 EXAM DUMPS WITH GUARANTEED SUCCESS!

Earning the Juniper JN0-663 certification is a valuable achievement for service provider network engineers who want to demonstrate their expertise and advance their careers. Service Provider Routing and Switching, Professional (JNCIP-SP) certification validates the skills needed to work with advanced routing and switching technologies and provides a competitive edge in the job market. Candidates who pass the JN0-663 exam will have the opportunity to work on complex service provider networks, supporting high-speed data, voice, and video services.

NEW QUESTION 18
Exhibit:

You must configure an OSPF virtual link to facilitate communication between Area 0 and Area 20.
Referring to the exhibit, which two addresses should you use as the neighbor IDs of the virtual link endpoints?
(Choose two.)

The address that is associated with R2’s router ID.

The address that is associated with R4’s router ID.

The address that is associated with R2’s xe-1/2/0 interface.

The address that is associated with R4’s xe-0/0/1 interface.

NEW QUESTION 19
Exhibit:

You have a Layer 3 VPN established between PE-1 and PE-2 as well as between PE-1 and PE-3. You are using a route reflector (RR-1) to distribute VPN routes to your IBGP peers. You are asked to ensure that only relevant routes are sent from RR-1 to each of the PE routers.
Referring to the exhibit, which statement is correct?

You should use VRF export policies on RR-1 to control which routes are sent to each PE router.

You should use route target filtering on RR-1 and all the PE devices to control which routes are sent to each PE router.

You should use firewall filtering on RR-1 and all the PE devices to control which routes are sent to each PE router.

You should use route target filtering only on RR-1 to control which routes are sent to each PE router.

NEW QUESTION 20
Exhibit:

You have an established Layer 3 VPN between two PE devices. You are asked to only send certain routes from PE-1 over the VPN to the remote site while maintaining all the routes on the PE-1 device. You created a policy that matches the specific routes and then tags these routes with the appropriate target community values.
In this scenario, which configuration changes must be made to satisfy the requirement?

Configure the export parameter and apply the policy to the my-ext-group BGP group configuration.

Configure the vrf-export parameter and apply the policy under the edit routing-instances vpn-a hierarchy.

Configure a RIB group and apply the policy as an import policy to routes distributed into the bgp I3vpn.0 routing table

Configure the import parameter and apply the policy to the my-ext-group BGP group configuration.

NEW QUESTION 21
Exhibit.

Referring to the exhibit, which two statements are correct for a route advertised by R1 towards R4? (Choose two )

The BGP next hop is set to 192.168.2 2 by R2

The BGP next hop is set to 14.1 1.1 byR2

The AS path is set to null by R2

The AS path is set to 150 by R2

NEW QUESTION 22
Exhibit:

The route shown in the exhibit is an example of which type of next-generation MVPN route?

Type 3 Selective MVPN autodiscovery route

Type 1 Intra-AS inclusive MVPN membership discovery

Type 2 Inter-AS inclusive MVPN membership discovery

Type 4 Selective MVPN autodiscovery route for leaf

NEW QUESTION 23
Exhibit:

All networks shown in the exhibit contain more than one BGP speaker You operate ISP A and must ensure that Customer Y sends their traffic to you over the directly connected link. Customer Y is not to be used for transit into your network.
What would you do to accomplish this task?

Advertise routes to Customer Y with the custom defined 65535:65535 community.

Advertise routes to Customer Y with the well-known no-export community

Advertise routes to Customer X with the well-known no-advertise community.

Advertise routes to Customer X with the custom defined 0:0 community

NEW QUESTION 24
Exhibit.

You are using EVPN to provide Layer 2 stretched VLANs between two sites You notice that the MAC addresses in either site are not showing up on the remote site.
Referring to the exhibit, what are two ways to solve this problem? (Choose two )

On R1, issue the sec 3wicch-cpt:.cr.3 vrf-target target: 65101:22030 Command

On R2 issue the set protocols evpn vni-options vni 22030 command

On R1, issue the sec protocols evpn vni-options vni 22030 vrf-target target:65101:22030 command

On R2, issue the set switch-options vrf-target target: 65101:22030 command

NEW QUESTION 25
Exhibit:

R2 is receiving the same route from R1 and R3. You must ensure that you can load balance traffic for that route.
Referring to the exhibit, which two configuration changes will allow load balancing? (Choose two.)

Configure muitipath under group R1.

Configure muitipath under the global BGP configuration.

Apply the prepend policy as an import policy under group R3.

Apply the prepend policy as an import policy under group R1.

NEW QUESTION 26
Which two statements about wide and narrow metrics used in IS-IS are correct? (Choose two)

Wide metrics are enabled with the wide-metrics-only parameter under protocols isis hierarchy.

Narrow metrics are enabled by default and use 8 bits in TLVs to send information.

Wide metrics are sent by default and use 24 bits in TLVs to send information.

Disabling narrow metrics results in external routes being leaked from L1 to L2 areas automatically.

With these TLVs, IS-IS metrics can have values up to 16,777,215 (224 – 1). By default, Junos OS supports the sending and receiving of wide metrics. https://www.juniper.net/documentation/us/en/software/junos/is-is/topics/concept/isis-wide-metrics.html

NEW QUESTION 27
Exhibit.

A network designer wants to ensure that traffic from R2 destined for 2001 db9:ffff:ff00. ’62 always traverses the R2-R1 link it that link is available Referring to the exhibit, which configuration change will satisfy this requirement?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

NEW QUESTION 28
Which two statements about IS-IS are correct? (Choose two.)

Level 1 intermediate systems exchange routing information with Level 1 intermediate systems in other IS-IS areas.

An IS-IS router sets the attached bit in the PDUs it sends to a Level 1 area to indicate that it is a backbone router.

A Level 1 router can only form adjacencies with other Level 1 routers.

Level 2 routers can form adjacencies with either Level 1 or Level 2 routers.

NEW QUESTION 29
Exhibit:

You are receiving the same 200.0.0.0/24 BGP route from four different ISPs.
Referring to the exhibit, which ISP’s route would be selected as active?

ISP-A

ISP-B

ISP-C

ISP-D

NEW QUESTION 30
Exhibit:

You notice an inconsistency between the routing table and the OSPF database, as shown in the exhibit.
What are two reasons for this behavior? (Choose two.)

The LSA is a Type 4 LSA.

An OSPF export policy is being applied to the route.

An OSPF import policy is being applied to the route.

The LSA is a Type 5 LSA.

NEW QUESTION 31
Exhibit.

You are troubleshooting a problem with a BGP peer where BGP routes are not being accepted from that peer Referring to the exhibit, which two statements are correct*? (Choose two )

Term 0 is missing a terminating action that allows BGP routes to be accepted

You cannot have terminating actions outside of terms.

The reject at the end of the policy is preventing the routes from being accepted.

Term 0 is missing a route-fitter that specifies the allowed routes

NEW QUESTION 32
You must deploy an interprovider VPN option that ensures that the ASBRs do not need to store any VPN routes.
In this scenario, which interprovider VPN option should you choose?

option B

option A

option C

option D

Extracted from: https://www.juniper.net/documentation/us/en/software/junos/vpn-l3/topics/topic-map/l3-vpns-interprovider.html
“Labeled IPv4 (not VPN-IPv4) routes are exchanged by the ASBRs to support MPLS. An MP-EBGP session between the end PE routers is used for the announcement of VPN-IPv4 routes. In this manner, VPN connectivity is provided while keeping VPN-IPv4 routes out of the core network.[…]”.

NEW QUESTION 33

You are provisioning Layer 2 circuits between sites CE1, CE2, and CE3.
Referring to the exhibit, which statement is true?