[Q13-Q34] 100% Passing Guarantee – Brilliant NS0-176 Exam Questions PDF [Mar-2023]

QUESTION 13
Which two are the expected outputs of network interface show? (Choose two.)

QUESTION 14
Exhibit:

An administrator is building a FlexPod configuration with UCS 6296 Fabric Interconnect devices that support legacy Fibre Channel 9FC) connections. The administrator uses UCS Manager to configure the unified ports on the Fabric Interconnect.
Referring to the exhibit, how many ports will FC use after the configuration is completed?

QUESTION 15
Exhibit:

Referring to the exhibit, what do the asterisks on the left indicate about the output of the ~show zoneset active~ command?

QUESTION 16
You have a FlexPod solution with Cisco 6296UP Fabric Interconnects. You currently have a direct-attached AFF8040 system using FCoE for storage connectivity. You would like to reconfigure the FlexPod so that the storage is connected through the upstream switches.
Using UCS Manager, which two steps would you perform to accomplish this task? (Choose two.)

QUESTION 17
A customer with several large Cisco MDS 9718 switches wants to reduce the number of total zones and the number of commands required to add devices, while still adhering to best practices.
In this scenario, which two configurations should be implemented? (Choose two.)

QUESTION 18
Which three are types of Storage Virtual Machines? (Choose three.)

QUESTION 19
Your company has acquired a new NetApp EF600 storage array with a 25 Gbps HIC.
In this scenario, which FlexPod-supported protocol should be used to connect to this array?

QUESTION 20
Click the Exhibit button.

On your NetApp storage system, you create a volume named datastore1, mount it to a junction path, and then set the correct export policy. When you attempt to mount the volume from VMware ESXi as a datastore, the server is unable to mount the path /datastore1. You verify that your existing NFS datastore (/datastore0) on the same NetApp storage system SVMis functioning normally.
Referring to the exhibit, what is preventing the server from mounting the new datastore?

QUESTION 21
Which feature allows Cisco Nexus 7000 Series switches to be virtualized at the device level?

QUESTION 22
What are two valid cluster interconnect switches? (Choose two.)

QUESTION 23
An administrator has a FlexPod solution using VMware vSphere 6.0. The ESXi hosts use iSCSI for storage connectivity, and all paths have been configured and connected between the NetApp cluster and the ESXi hosts.
Virtual Storage Console has been installed and ESXi host-recommended settings have been applied to all hosts. The active LUN path for one of the iSCSI datastores experiences a connectivity failure and the LUN switches to a new active path.
In this scenario, which event would trigger the ESXi host to switch the active LUN path again?

QUESTION 24
You are attempting to establish a cluster peer relationship between two NetApp clusters, but the peering process fails.
What is a cause for this failure?

QUESTION 25
You are an administrator of a UCS system. You notice that when you apply a setting that requires a reboot, the affected hardware reboots immediately without warning. You would like to reboot to be acknowledged by an administrator instead.
What should you do to accomplish this task?

QUESTION 26
Which backup type stores Service Profile information as a small editable file?

QUESTION 27
Which set of commands maps VLAN 100 to VSAN 100?

QUESTION 28
In which two locations is the VSAN ID configured in a FlexPod solution? (Choose two.)

QUESTION 29
You are asked to install the Virtual Supervisor Module (VSM) software on a Nexus 1000v switch.
Which two sources would you use to install this software? (Choose two.)

QUESTION 30
The NetApp Vistual Storage Console is used to set which three setting categories on ESXi hosts? (Choose three.)

QUESTION 31
Which service may be used to manage users and groups in a vSphere environment?

QUESTION 32
Which statement is true for Fibre Channel QoS System Class?

QUESTION 33
Your primary VSM needs to be edited, rebooted, or migrated. You need to initiate a manual switchover to your standby VSM.
What command will allow this to occur?

QUESTION 34
Exhibit:

You have a NetApp cluster and have just performed a storage failover giveback command from the CLI.
Referring to the exhibit, what is the status of the storage failover process?