Updated Oct-2023 Exam Engine for HPE6-A45 Exam Free Demo & 365 Day Updates [Q73-Q94]

5/5 - (1 vote)

Updated Oct-2023 Exam Engine for HPE6-A45 Exam Free Demo & 365 Day Updates

Exam Passing Guarantee HPE6-A45 Exam with Accurate Quastions!

NEW QUESTION 73
Refer to the exhibit.

A network administrator needs to alter myACL so that it permits all traffic that arrives in VLAN 2 and is destined to 10.1.10.0/24. Besides this change, the ACL must continue to act as it does now. The administrator plans this new rule:
permit ip any 10.1.10.0/24

Apply the new rule without a rule ID to ensure that the switch applies the automatic processing order to it.

Resequence the ACL with more space, then add the new rule with a sequence ID before the ID for the current third rule.

Remove the ACL from the VLAN and re-apply it as an inbound VLAN ACL (VACL). Then, add the new rule with any ID higher than 2.

Enable ACL grouping on the switch. Add the new rule in anew ACL. Then, group the new ACL with myACL.

NEW QUESTION 74
Which technologies can prevent split brain in a VSF fabric that includes Aruba 2930F switches?

ARP MAD or OOBM MAD

VLAN MAD or ARP MAD

OOBM MAD or LLDP MAD

LLDP MAD or VLAN MAD

NEW QUESTION 75
Refer to the exhibits.
Exhibit 1

Exhibit 2

A company does not require authentication for security, but AOS-Switches are set up to use local MAC authentication (LMA) to assign the correct VLAN and priority to IP phones. IP phones and computers belong to different VLANs. Each device is supposed to connect to a specific port, but sometimes users connect their devices to the wrong ports and cannot receive access without help from IT.
How can a network administrator configure the switches to eliminate this issue?

Set the address limit to 2 on the switch ports that apply LMA.

Create a user role that applies the user VLAN, and set this role as the initial role.

Add the MAC addresses for computers to the myPhones MAC group.

Apply LMA to all edge switch ports, and set the unauth VLAN to the user VLAN.

NEW QUESTION 76
Exhibit

The network administrator enables DHCP snooping globally and on VLAN 2.
An additional step is mandatory for DHCP snooping to operate correctly and for clients to receive HDCP settings.
What is the additional mandatory step?

Define trk1 as a trusted DHCP port.

Define an authorizes DHCP server.

Enable ARP protection.

Define edge ports as untrusted DHCP ports.

NEW QUESTION 77
Refer to the exhibits.
Exhibit 1.

Exhibit 2.

The company wants to minimize congestion on Link 1.
Which spanning tree implementation meets this goal?

Instance 1 = VLANs 4-5 Instance 2 = VLANs 6-7
Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1
Switch 3 instance 1 priority = 1 Switch 3 instance 2 priority = 0

Instance 1 = VLANs 4,6 Instance 2 = VLANs 5,7
Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1
Switch 3 instance 1 priority = 1 Switch 3 instance 2 priority = 0

Instance 1 = VLANs 4,6 Instance 2 = VLANs 5,7
Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1
Switch 3 instance 1 priority = 0 Switch 3 instance 2 priority = 1

Instance 1 = VLANs 4-5 Instance 2 = VLANs 6-7
Switch 2 instance 1 priority = 0 Switch 2 instance 2 priority = 1
Switch 3 instance 1 priority = 0 Switch 3 instance 2 priority = 1

NEW QUESTION 78
Refer to the exhibits.
Exhibit 1.

Exhibit 2.

The VoIP phone connects, authenticates successfully, and is dynamically assigned to tagged VLAN 6. The endpoint connected to the phone does not authenticate but starts to send untagged traffic.
How does the switch handle this traffic?

It forwards the traffic in VLAN 5.

It relays the traffic to the RADIUS server for authentication.

It forwards the traffic in VLAN 6.

It drops the traffic.

NEW QUESTION 79
Refer to the exhibit.

Several interfaces on an AOS-Switch enforce 802.1X to a Radius server at 10.254.202.202. The interface 802.1X settings are shown in the exhibit, and 802.1X is also enabled globally. The security team have added a requirement for port security on the interfaces as well. Before administrators enable port security, which additional step must they complete to prevent issues?

Set 802.1X client limit on the interfaces.

Manually add legitimate MAC addresses to the switch authorized MAC list.

Enable DHCP snooping on VLAN 20.

Enable eavesdropping protection on the interfaces.

NEW QUESTION 80
Refer to the exhibit.

An administrator created a backplane stack with the plug-and-play method, and did not alter the default backplane stacking settings. Later, two backplane stacking links failed, as shown in the exhibit.
What happens to the backplane stack after the failures?

The standby becomes the commander of its fragment, which remains active. The fragment with the commander becomes inactive.

The fragment that contains the commander operates at Layer 2 and layer 3, and the other fragment operates at layer 2 only.

The fragment that contains the commander remains active, and the fragment with the standby member is disabled.

The standby becomes the commander of its fragment. Both fragments remain active and operate at both Layer 2 and Layer 3.

NEW QUESTION 81
Refer to the exhibit.

The routing switches shown in the exhibit use OSPF, and all of their interfaces are in Area 1. A faulty link on Switch-1 went up and down many times over the course of several hours. This caused link state updates (LSUs) to flood all of the routing devices in the OSPF AS and reduce performance. The network administrator fixed the faulty link on Switch-1, but the administrator also wants to mitigate the effects if a similar issue occurs in the future.
Which design improvement would help?

Configure Area 1 as a stub area on all routers except Switch-2, Switch-3, and Switch-4

Divide the AS into different areas, and aggregate routes between them

Divide the AS into different areas, and configure the backbone area as an NSSA

Decrease the LSA generation timer, and make sure to set the same value on all routers

NEW QUESTION 82
Refer to the exhibit.

A company has IP phones that are LLDP-MED capable. The exhibit shows the configuration for the VLAN to which IP phones belong, as well as the configuration for ports to which phones will connect. AOS-Switches at the access layer are set up to use LLDP-MED. The administrator wants to automatically provision the phones to send traffic with the right VLAN tag and priority.
Which additional configuration step must the administrator complete?

Specify LLDP-MED as the global LLDP mode

Specify the voice setting in VLAN 3

Enable LMA and configure the proper LMA profiles

Enable 802.1X and MAC-based VLANs on the ports

NEW QUESTION 83
What is one difference between BPDU protection and root guard?

BPDU protection works with RPVST+, RSTP, and MSTP. Root guard works with RSTP or MSTP, but not RPVST+.

BPDU protection blocks a port if it receives any BPDU, but root guard blocks a port only if the BPDU indicates a better root path.

BPDU protection is typically implemented on edge ports, but root guard is typically implemented on uplinks with the root port role.

BPDU protection drops BPDUs received on a port, but does not block the port. Root guard blocks the port if it receives a BPDU.

NEW QUESTION 84
Refer to the exhibit.

Switch-2, Switch-5, and Switch-6 currently have many OSPF routes to Area 1 networks. The network administrator wants to replace these routes with a single aggregated route to 10.1.0.0/16 on each switch.
Where should the administrator specify the 10.1.0.0/16 range?

in the Switch-2 OSPF Area 2 configuration

in the Switch-1 OSPF Area 0 configuration

in the Switch-1 OSPF Area 1 configuration

in the Switch-2, Switch-5, and Switch-6 OSPF global configuration

NEW QUESTION 85
Refer to the exhibits.
Exhibit 1

Exhibit 2

The network administrator enters the commands shown in Exhibit 2. What is the spanning tree status on A1 and A2?

Both A1 and A2 forward traffic.

A1 forwards traffic, and A2 blocks traffic.

A1 blocks traffic, and A2 forwards traffic.

Both A1 and A2 block traffic.

NEW QUESTION 86
Refer to the exhibits.
Exhibit 1

Exhibit 2

The IP phone in the exhibit is set up to complete 802.1x authentication to the network. How can the netwotk administrator prevent a user on the computer from receiving network access without authentication?

Set an 802.1X client limit of 2 on interface 1.

Set up the MAC filter on interface 1.

Enable static mode port security on interface 1.

Enable MAC-based VLANs on interface 1.

NEW QUESTION 87
Refer to the exhibits.
Exhibit 1

Exhibit 2

Switch-1 has a power issue that causes it to fail. When Switch-1 comes back up, endpoints lose connectivity for a few minutes. The network administrator decides to enter this command on Switch-1:
Switch-1 (config)# vlan 10 vrrp vrid 10 preempt-delay-time 120
Exhibit 2 shows the VRRP configuration just after the change. What is the effect of this change?

Switch-1 and Switch-2 both become Master in their own VRRP virtual router due to the delay timer mismatch. The mismatch must be fixed.

Switch-1 now waits to take over as Master if it fails and recovers. This should prevent the connectivity issue from occurring again.

Switch-1 experiences an internal error in the VRRP process. This error causes Switch-2 to take over as Master for VLAN 2.

Switch-1 continues to act as it did before the preempt delay time was set. Administrators must plan additional changes to fix the issue.

NEW QUESTION 88
Refer to the exhibit.

Several interfaces on an AOS-Switch enforce 802.1X to a Radius server at 10.254.202.202. The interface
802.1X settings are shown in the exhibit, and 802.1X is also enabled globally. The security team have added a requirement for port security on the interfaces as well. Before administrators enable port security, which additional step must they complete to prevent issues?

Set an 802.1X client limit on the interfaces.

Manually add legitimate MAC addresses to the switch authorized MAC list.

Enable DHCP snooping on VLAN 20.

Enable eavesdropping protection on the interfaces.

NEW QUESTION 89
Refer to the exhibit.

AOS-Switches will enforce 802.1X authentication on edge ports. The company has two RADIUS servers, which are meant to provide redundancy and load sharing of requests. The exhibit shows the planned RADIUS settings to deploy to the switches.
What should customers understand about this plan?

AOS switches do not support two RADIUS servers for redundancy, instead, a secondary authentication method is required.

Dynamic authentication is only permitted on one of the RADIUS servers and must be removed from the other.

Each RADIUS server must use a unique port number for the authentication and dynamic authorization port.

Each AOS-Switch will send all RADIUS requests to the first server on the list unless that server becomes unreachable.

NEW QUESTION 90
Refer to the exhibit.

Switch-2, Switch-5, and Switch-6 currently have many OSPF routes to Area 1 networks. The network administrator wants to replace these routes with a single aggregated route to 10.1.0.0/16 on each switch.
Where should the administrator specify the 10.1.0.0/16 range?

in the Switch-2 OSPF Area 2 configuration

in the Switch-1 OSPF Area 0 configuration

in the Switch-1 OSPF Area 1 configuration

in the Switch-2, Switch-5, and Switch-6 OSPF global configuration

NEW QUESTION 91
Network administrators need to track when traffic, matches deny entry in an ACL applied to a port. They want the alert to be sent to a syslog server that is already set up to send logs.
What should administrators do to enable the alerts?

Specify the log option for the ACL entry, and enable ACL debugging.

Set the debug destination to session, and enable ACL debugging

Enable ACL debugging, and enable SNMP port security traps

Specify the log option for the ACL entry, and enable SNMP port security traps.

NEW QUESTION 92
Refer to the exhibits.
Exhibit 1

Exhibit 2

A company does not require authentication for security, but AOS-Switches are set up to use local MAC authentication (LMA) to assign the correct VLAN and priority to IP phones. IP phones and computers belong to different VLANs. Each device is supposed to connect to a specific port, but sometimes users connect their devices to the wrong ports and cannot receive access without help from IT.
How can a network administrator configure the switches to eliminate this issue?

Set the address limit to 2 on the switch ports that apply LMA.

Create a user role that applies the user VLAN, and set this role as the initial role.

Add the MAC addresses for computers to the myPhones MAC group.

Apply LMA to all edge switch ports, and set the unauth VLAN to the user VLAN.

NEW QUESTION 93
Exhibit

The VoIP phone connections, authenticates successfully, and is dynamically assigned to tagged VLAN6. The endpoint connected to the phone does not authenticate but start to send untagged traffic. How does the switch handle this traffic?

It forwards the traffic in VLAN 5.

It relays the traffic to the RADIUS server for authentication.

It forwards the traffic in VLAN 6.

It drops the traffic

NEW QUESTION 94
Refer to the exhibits.
Exhibit 1

Exhibit 2

A company does not require authentication for security, but AOS-Switches are set up to use local MAC authentication (LMA) to assign the correct VLAN and priority to IP phones. IP phones and computers belong to different VLANs. Each device is supposed to connect to a specific port, but sometimes users connect their devices to the wrong ports and cannot receive access without help from IT.
How can a network administrator configure the switches to eliminate this issue?

Set the address limit to 2 on the switch ports that apply LMA.

Create a user role that applies the user VLAN, and set this role as the initial role.

Add the MAC addresses for computers to the myPhones MAC group.

Apply LMA to all edge switch ports, and set the unauth VLAN to the user VLAN.

HP HPE6-A45 Certification Exam is an important certification for professionals who want to specialize in Aruba switching solutions. Aruba Certified Switching Professional Exam certification is ideal for network administrators, network engineers, and network architects who want to gain a deeper understanding of Aruba switching technologies. By passing HPE6-A45 exam, you will demonstrate that you have the necessary skills to configure and troubleshoot complex Aruba switching solutions, which can help you advance your career and increase your earning potential.

HPE6-A45 certification exam is designed for network professionals who are looking to enhance their skills in deploying, managing, and troubleshooting enterprise-level Aruba campus switching solutions. Aruba Certified Switching Professional Exam certification is awarded to individuals who demonstrate their expertise in configuring and verifying ArubaOS-Switches, VLANs, and link aggregation, among other key areas. Aruba Certified Switching Professional Exam certification is vendor-agnostic, meaning that it is not limited to Aruba products but covers a wide range of switching technologies.

Exam Questions for HPE6-A45 Updated Versions With Test Engine: https://www.actualpdf.com/HPE6-A45_exam-dumps.html

Leave a Reply Cancel reply