[Jul 14, 2023] New 2023 Cisco 300-615 Exam Dumps with PDF from ActualPDF (Updated 169 Questions) [Q76-Q92]

Rate this post

New 2023 300-615 exam questions Welcome to download the newest ActualPDF 300-615 PDF dumps (169 Q&As)

P.S. Free 2023 CCNP Data Center 300-615 dumps are available on Google Drive shared by ActualPDF

Q76. A fabric interconnect fails to start and the console displays the loader prompt. Which two actions resolve the issue? (Choose two.)

Load an uncorrupt bootloader image.

Load an uncorrupt kickstart image.

Reconnect L1/L2 cables between the Fis.

Reformat the fabric interconnect.

Load the correct version of the boot image.

Q77. The Cisco Nexus switch is connected to a peer switch that is not running Cisco NX-OS. The switches are connected using port channel and are experiencing packet loss. Which action should be performed on the Cisco Nexus switch ports to resolve this issue?

Turn on lacp suspend-individual.

Turn on lacp graceful-convergence.

Turn off lacp graceful-convergence.

Turn off lacp suspend-individual.

Q78. Refer to the exhibit.

An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?

Configure the role name to match the group name on Microsoft Active Directory.

Include specific users into MDS role configuration.

Configure SSH logins on Cisco MDS switch.

Integrate Cisco MDS with Microsoft Active Directory.

Q79. An engineer is implementing, Fibre Channel (FC) switching on a Cisco 9000 Series Switch, but the procedure fails with the message “FC traffic is not being routed through the fabric.”. Which action resolves the issue?

Configure the FSPF for VSAN 10 on the NX9k-01-LAB switch.

Set the FSPF interface link cost to be less than 30,000 in the IVR path.

Set the FSPF hello interval on fc12 interface the NX9k-01-LAB switch.

Configure the VSAN ID 10 on the link connected to fc1/12.

Q80. Refer to the exhibit.

The integration between Cisco UCS Manager and Cisco UCS Central failed. Which action resolves the issue?

Implement the consistent NTP source between the appliances

Implement the connectivity between the appliances through a firewall

Configure the certificate between the appliances

Configure the shared secret key between the appliances

Q81. Refer to the exhibit.

The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?

switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

Q82.

Refer to the exhibit. Interface fc1/5 is offline. Which action should be taken to troubleshoot the issue?

Activate the correct zoneset for VSAN 100.

Update the FLOGI database to contain the FLOGI entries for interface fc1/5 in VSAN 100.

Update the FCNs database to contain names for VSAN 100.

Configure the upstream ports and the server ports to be in VSAN 100.

Q83. Refer to the exhibit.

During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit. Which action resolves the issue.

Reconfigure the Drive Type from “Removable” to “Non-Removable”

Insert an SD card into SLOT-2

Configure the RAID that is associated with the card.

Set SLOT-1 Sync Mode to “Auto”

Q84. Refer to the exhibit.

After a failover occurs, which two actions must be performed on Switch-B to manually preempt the operational primary role back to Switch-A? (Choose two.)

Configure the local vPC role priority to have a lower value than Switch-A.

Configure the local vPC role priority to have a higher value than Switch-A.

Disable and then re-enable the vPC peer-keepalive link.

Configure the local vPC role priority to have the same value as Switch-A.

Disable and then re-enable the vPC peer link.

Q85. Refer to the exhibit.

An engineer discovers that if the vPC peer link goes down, half of the devices in VLAN 20 experience connectivity issues with the external networks Which action resolves the issue?

Configure a dedicated Layer 3 link between vPC peers

Allow non-vPC VLANs on a second trunk between the two vPC peers

Add the non-vPC SVIs in the dual-active exclude VLAN list

Exclude the non-vPC VLANs from vPC peer link

Q86. Refer to the exhibit.

Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. Which statement describes what happens in this scenario?

Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.

Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.

Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.

Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.

Q87. Refer to the exhibit.

A network engineer traces the packet flow from the Veth991 of a blade server toward the core switch. The switch reports performance issues What is the role of the interface Eth1/7?

IOM network interface

fabric interconnect uplink interface

IOM host interface

server interface

Q88. Refer to the exhibit.

Refer to the exhibit. VSAN traffic is not routed as expected. Which action should be taken to resolve the issue?

Reset the error packet counter

Configure the hello timer to match the neighbor

Configure the FSPF dead interval with a value higher than 80 seconds

Reset the inactivity timer on switch-2

Q89.

Refer to the exhibit. One of the vPC VTEPs fails to route VXLAN traffic to vPC connected hosts. When the issue was being diagnosed, it was discovered that the packets that were expected to be forwarded to the MAC address on the SWITCH-VTEP-1 are instead forwarded to the MAC address on SWITCH-VTEP-2 and then dropped. Which action resolves the issue?

Configure a distributed anycast gateway on both peers

Configure ip arp synchronize under the VPC domain on both peers

Configure peer-gateway under the VPC domain on both peers

Configure a different secondary IP address for one of the vPC peers

Q90. Refer to the exhibit.

An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action resolves the issue?

Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.

Set the local group number as 300 in the remote data center configuration

Run version 1 and version 2 HSRP on VLAN300 in the local data center.

Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.

Q91. You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?

The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.

Rebooting the APICs and the leaf and spine switches after wiping them is not required.

You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.

The same Fabric Name value should be used before after wiping all devices.

Q92. Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.