Valid HCIA-5G H35-480_V3.0 Dumps Ensure Your Passing [Q12-Q32] – Unlimited Lifetime Access Free Exams PDF

5/5 - (1 vote)

Valid HCIA-5G H35-480_V3.0 Dumps Ensure Your Passing

H35-480_V3.0 Dumps Real Exam Questions Test Engine Dumps Training

Huawei H35-480_V3.0 is the latest and updated version of HCIA-5G-RAN certification exam. HCIA-5G-RAN V3.0 certification is designed to test and validate the skills of professionals who work in the 5G radio access network domain. The HCIA-5G-RAN certification is the first step towards becoming a 5G technology expert, and H35-480_V3.0 is the perfect opportunity to upgrade your skills and take your career to the next level.

NO.12 Which of the following 5G massive MIMO scenarios is more suitable for high rise office building coverage?

H45V12

H25V25

H110V6

H45V6

NO.13 What is the required distance between a CPE and a gNodeB in a 5G network test?

Less than 10m

Greater than 5m

Less than 5m

Greater than 10m

NO.14 Which of the following NR slot configurations are defined in 3GPP specifications?

Mixed slot, which contains at least one downlink/uplink symbol while other symbols can be flexibly configured

Flexible-slot (all symbols are flexibly configured)

Downlink-only slot (all symbols are dedicated for downlink)

Uplink-only slot (all symbols are dedicated for uplink)

NO.15 Which of the following messages is the first message sent by a gNodeB to an AMF?

NGAP_UL_NAS_TRANSP

RRC_SETUP

NGAP_INIT_CONTEXT_SETUP_RSP

NGAP_INIT_UE_MSG

NO.16 SSB GSCN is the center frequency number of an NR cell.

True

False

NO.17 According to 5G eMBB service requirements, which of the following is the minimum rate required for network edge coverage?

1Gbps

100Mbps

1Mbps

10Gbps

NO.18 In what scenarios is GENEX Assistant typically applied?

Wireless network adjustment

Single site verification

Batch processing of gNodeB alarms

Routine network optimization

NO.19 In the inter-site DC solution, the X2 interface can be used to implement transmission interconnection between the LTE and NR sites. Which of the following is the requirement of the transmission delay in such case?

<40ms

<10ms

<30ms

<20ms

NO.20 During 5G single site verification, you only need to test the user access and rate. Other test items are analyzed in drive tests.

True

False

NO.21 During single site verification, which of the following messages can be traced by the Probe to analyze problems?

L3 Messages

Xn Messages

L1 Messages

NG Messages

NO.22 Which of the following is the correct sequence for adding gNodeB hardware?

RF unit -> Subrack -> Board -> Cabinet

Board -> Cabinet -> Subrack -> RF unit

Cabinet -> Subrack -> Board -> RF unit

Subrack -> Board -> Cabinet -> RF unit

NO.23 E2E network device update is required for the evolution from 5G NSA networking to SA networking.

True

False

NO.24 If the length of the CPRI optical fiber between a BBU and an RRU exceeds 150 m, you are advised to use a multimode fiber.

True

False

NO.25 During a 5G test, a portable computer is directly connected to the LAN port of the Huawei CPE through a network cable to obtain a dynamic IP address for communication.

True

False

NO.26 On an NSA network, the eNodeB immediately triggers the SgNB addition procedure after a UE attaches to the LTE network. If the SgNB addition fails, the eNodeB attempts to add the SgNB again until it is successful.

True

False

NO.27 5G inherits the frame structure of 4G, but the slot length can be adjusted based on different SCSs. Which of the following is not a 5G slot length?

0.5ms

10ms

0.25ms

1ms

NO.28 C-band is the most popular frequency band for 5G network deployment. However, there is an imbalance between uplink and downlink coverage – how much does this imbalance approximately amount to?

5dB

3dB

12dB

20dB

NO.29 C-band is the most popular frequency band for 5G network deployment. However, there is an imbalance between uplink and downlink coverage – how much does this imbalance approximately amount to?

5dB

3dB

12dB

20dB

NO.30 Which of the following methods can be used by a gNodeB to obtain downlink channel characteristics?

DMRS of the uplink PUSCH of the UE

Downlink DMRS signal

UE-reported uplink PMI

Uplink SRS signal

NO.31 gNodeBs periodically send TPC commands to UEs over PDCCHs to control the transmit power of which of the following uplink channels or signals of UEs? (Choose All that Apply)

SRS

PUSCH

PUCCH

NO.32 The purpose of replaying logfiles is to reproduce the test process. The GENEX Probe can work without license in this case.

True

False